Variable TOOL_MESSAGES_ENConst

Type Declaration

• Readonlytool.arc: "Arc"

• Readonlytool.arc.end: "Arc: click the end point."

• Readonlytool.arc.mid: "Arc: click a point on the arc."

• Readonlytool.arc.start: "Arc: click the start point."

• Readonlytool.circle: "Circle"

• Readonlytool.circle.center: "Circle: click the center."

• Readonlytool.circle.radius: "Circle: click a point on the circle or type the radius."

• Readonlytool.dimension: "Dimension"

• Readonlytool.dimension.first: "Dimension: click the first point (snap to an object to keep it associated)."

• Readonlytool.dimension.place: "Dimension: click where the dimension line goes."

• Readonlytool.dimension.second: "Dimension: click the second point."

• Readonlytool.extend: "Extend"

• Readonlytool.extend.pick: "Extend: click near the end to extend."

• Readonlytool.line: "Line"

• Readonlytool.line.end: "Line: click the end point or type a length (Shift = horizontal/vertical)."

• Readonlytool.line.start: "Line: click the start point."

• Readonlytool.move: "Move"

• Readonlytool.move.base: "Move: click the base point."

• Readonlytool.move.select: "Move: select objects first (click one)."

• Readonlytool.move.target: "Move: click the destination or type dx,dy."

• Readonlytool.pan: "Pan"

• Readonlytool.path: "Path"

• Readonlytool.path.next: "Path: click or drag the next point; Enter finishes, click the start to close."

• Readonlytool.path.start: "Path: click to start; drag to pull a curve handle."

• Readonlytool.polyline: "Polyline"

• Readonlytool.polyline.next: "Polyline: click the next point; Enter or double-click finishes, click the first point to close."

• Readonlytool.polyline.start: "Polyline: click the first point."

• Readonlytool.rect: "Rectangle"

• Readonlytool.rect.end: "Rectangle: click the opposite corner or type width,height."

• Readonlytool.rect.start: "Rectangle: click or drag from a corner."

• Readonlytool.rotate: "Rotate"

• Readonlytool.rotate.center: "Rotate: click the center or type an angle after it."

• Readonlytool.rotate.reference: "Rotate: click the reference direction or type an angle in degrees."

• Readonlytool.rotate.select: "Rotate: select objects first (click one)."

• Readonlytool.rotate.target: "Rotate: click the new direction."

• Readonlytool.scale: "Scale"

• Readonlytool.scale.base: "Scale: click the base point."

• Readonlytool.scale.reference: "Scale: click a reference point or type a factor."

• Readonlytool.scale.select: "Scale: select objects first (click one)."

• Readonlytool.scale.target: "Scale: click the new position of the reference point."

• Readonlytool.select: "Select"

• Readonlytool.select.dragging: "Release to place."

• Readonlytool.select.dragRejected: "This position breaks a rule; the nearest allowed position is shown."

• Readonlytool.select.prompt: "Click to select, drag to select an area (right-to-left touches), drag objects to move."

• Readonlytool.split: "Split"

• Readonlytool.split.pick: "Split: click a curve where it should be cut."

• Readonlytool.text: "Text"

• Readonlytool.text.position: "Text: click where the text starts."

• Readonlytool.text.type: "Text: type, then Enter (Shift+Enter for a new line, Escape cancels)."

• Readonlytool.trim: "Trim"

• Readonlytool.trim.pick: "Trim: click the piece to remove."